High Quality Plastic Recycling to Fuel, Rubber Circulated Pyrolysis Plant, Cracking Machine for Rubber Suppliers in China

Home > Products > Waste Rubber Pyrolysis Plant > Placstic\Rubber recycled to fuel oil pyrolysis equipment

Placstic\Rubber recycled to fuel oil pyrolysis equipment

Basic Info

Model No.: LJ-9

Product Description

Placstic\Rubber Recycled to Fuel Oil Pyrolysis Equipment


Introduction of Shangqiu Sihai Energy Technology Co., Ltd

Our company is located in Chenfeng Avenue, Pingtai Economical Development Zone, Shangqiu, Henan, China. It covers an area of 75,000 square meters, of which there are two modern production workshops cover an area of 60,000 square meters. Our company mainly engaged in waste rubber, waste plastics, waste tires, waste aluninum foil, waste mineral oil and other environmental pyrolysis equipment, distillation equipment and peripheral ancillary equipment processing production and sales. Company annual output is more than 400 sets of environmental protection equipment. Our products have been exported to Europe and the United States, South Africa, Southeast Asia, the Middle East and the Mainland and other 36 countries and regions.



Features of Placstic\Rubber Recycled to Fuel Oil Pyrolysis Equipment
a. In the design of pyrolysis key device, completely overcome the local heat uneven, easy to break, low yield, short life and other unfavorable factors of the current vertical flat bottom pyrolysis plant.

b. With fast and practical feed and slag system.

c. Efficient gas heating system. In the process of refining, when the heated gas reaches 150 degrees Celsius, it will produce a lot of gas which can not be liquefied in normal temperature and pressure methane to butane.These gases are fully burned by specially designed gas nozzles, will produce a lot of energy which greatly saves energy.

d.Flue dust removal system has a desulfurization dust cather(qualified), equipped with two ways water impact cyclone dust removal chamber, which can ensure the discharge of flue outlet reach safe discharge standard.



Technical Parameters of Placstic\Rubber Recycled to Fuel Oil Pyrolysis Equipment

Model

Raw material

Structure form

Cooling system

LJ-9

Waste tire, plastic,rubber

Horizontal

Water cooling

Heating method

oil output rate

Power

Installation

Directly

45%

5.5KW

Foundation



Working process of Placstic\Rubber Recycled to Fuel Oil Pyrolysis Equipment

First, two or three workers put waste tires into the host reactor from the feed gate, close the feed gate, and seal. Then start the fire and heat the main furnace with fuel coal or wood in the heating chamber. When the temperature reaches 150°C, part of the gas will precipitate (at this time most of the gas is exhaust gas). When the temperature reaches 220°C, oil and gas will precipitate and enter the gas distribution package. The residual oil (including some slag) will sink to the residue. Oil tanks, while light oils automatically enter the water cooling system, cooling, liquefaction. Enter the light tank. In this way, heavy oil and light oil can be obtained.

Secondly, after condensation, some of the gas that cannot be condensed is called exhaust gas. The exhaust gas passes through a safe setting - the water seal. (The role of the water seal is to prevent the open flame from collapsing from the combustion chamber and the exhaust gas.) Return to the heating chamber as Fuel heating furnace. Therefore, at the beginning of the equipment operation, the fuel was coal or wood. When the temperature rose to 220°C-270°C, the exhaust gas could be used as a fuel. Under normal circumstances, the fuel needed per ton of waste tires is 60kg.

Finally, the soot treatment: smoke from the main furnace and the housing out of the middle, into the flue condensation system, and then enter the desulfurization dust tower, desulfurization dust tower inside there are three processes: water, magnetic ring, stainless steel nozzle (atomizing, filtering smoke), The smoke is filtered and purified. More than 90% of the discharged gas is steam, free from pollution.

Electricity consumption: The power consumption of the whole set of equipment includes: induced draft fan (4-7.5KW), reducer (3--5.5KW), water pump (1.5KW) and oil pump (1.5KW). A total of 10-16 kW, so the entire operation process, the power consumption is minimal.

Treatment of the raw material

Hydraulic automatic feeding in

Automatic slag-outpyrolyzerdesulphurization and deduster

↓ ↓

Air package draft fan

↓ ↓

1st tube condenser first 2nd purifier

↓ ↓

2nd tube condenser second 2nd purifier

↓ ↓

Cooling tower calandria condenser emission reach the standard

Oil and gas separator product oil

Water seal explosion-proof machine




Shangqiu Sihai Energy Technology Co., Ltd. after-sales service guarantee:

1. On the day of receipt of the prepayment of the equipment, technical personnel will be arranged to guide the foundation on the spot within one week.

2.Delivery is 15~20 days from the date of receipt of the advance payment, and technical personnel are sent to the site for free guidance, installation, commissioning and training on the same day or within three days of shipment to ensure that the machine can return after normal operation.

3. Lifetime warranty.

4. Different raw materials need the same machine, mainly because there are some differences in the cracking process. Our technicians will provide you with free operation training. You can also send raw material samples to our company to make free oil rate tests on your raw materials.









Contact us if you need more details on Plastic Recycling to Fuel. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Rubber Circulated Pyrolysis Plant、Cracking Machine for Rubber. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Waste Rubber Pyrolysis Plant

Email to this supplier
  • *Subject:
  • To:

  • *Messages:
    Your message must be between 20-8000 characters